Electronic Vaporizer for Both Dry Herb and Wax Atman Starlight
1. Turning on the Starlight
Click the power button for 5 times in 2 seconds, and the four small
lights will flash 3 times to indicate the device power on.
2. Loading the Starlight
Open the glass mouthpiece and magnet cap, and fill the chamber with
flower or wax.
For dry herb, maximum fill 2/3 of chamber will be the best
For Wax, maximum fill 1/2 of chamber will be the best
Then close the cap and mouthpiece and choose a desired temperature
level. Waiting for the light turn to solid and then you can begin
to smoke without holding the power button.
Operation with the temperature control system
1. Change the temperature levels: Turn on the device, and there
will be a setting level already (different items have different
setting) light one, then click the power button for 3 times in 2
seconds. Meantime temperature will turn to the next level and flash
3 times. When the temperature reaches to the highest level, the
device will cycle change from the lowest one.
2. Heating: Hold the power button for 3 seconds, the power button
will turn to red and the chosen small light will light on. when
reaching the temperature set, the power button will turn to green.
And last minutes for vape.
3. Stop heating: Hold the power button for 3 seconds, the power
button and four small lights will turn off together which indicates
the device stop heating.
1. Click the power button for 5 times in 2 seconds, and the four
small lights will flash 3 times to indicate the device power off.
Make sure the device is not heating before turning off the device
Temperature control system
1. 230F, blue light
2. 320F, blue light
3. 410F, yellow light
4. 500F, yellow light
1. Charging: with USB charge, and the four small lights will flash
2. Finish charging: when the voltage reach to 4.13v, all four small
lights will turn off and the power button will flash 10 times in
green and then turn off. Press the power button, all the lights
will be on which indicates charging is finished.
3. Being charged:
0%-25%, the first light will flash
25%-50%, the first light will on and second light will flash
50%-75%, the first and seconds lights will on, and the third one
75%-100%, the three lights will on together, the last one will
1. over-time protection: 5 minutes protection, it will stop working
and the red, green LED light will flash together 5 times in 5
(Attention: The device will turn off if the low voltage warning
happen 5 times)
2. Short-cut protection: the red LED light will flash 7 times when
the short-cut happen and it will stop working
3. Over-load protection: the power button will flash 3 times in red
when resistance below 0.2ohm.
4. Heat sensor short-cut protection: heating sensor not install
well, green LED light will flash 5 times and the device will stop
Battery capacity: 28000mah
Battery type: Li-ion
Time to full charge: 3-4hours
After the device clam down, take out of the heating chamber and
then clean inside with brush or you can also disinfect it with
ATMAN Starlight comes with 1 year warranty. If your Starlight
breaks during warranty coverage, we will fix it or replace it.
Starlight starter kit comes with
1x starlight device
1x stainless steel spoon
1x cleaning brush
1x usb charger
1x user manual
1x gift case
|Product Name||Atman Starlight|
|Usage||Dry Herb and Wax|
|Features||With Custimization Service|
|Chamber Material||Stainless Steel|
Do not expose your Starlight to external heart about 500F
Do not puncture or incinerate
Do not dismantle the Starlight beyond the cleaning and maintenance
instructions which will void the warranty
Do not drop or crush the Starlight
Do not use if damaged
Dispose of battery in accordance with local regulations
Use only provided power supply to charge battery. User of any power
supply is dangerous and will void the warranty